Independent guide · Crypto

Price impact vs slippage: read a swap quote correctly

Compare 1,000 reference tokens, a 960-token quote and 955 received. Calculate impact, slippage and minimum output without counting costs twice.

Editorial illustration: comparing quantities and costs

Your swap shows 4% price impact and 1% slippage tolerance. Those figures are not two fees to add. Price impact concerns the effect of your own trade; slippage compares the quote with execution. If a 1,000-token reference becomes a 960-token quote, a 1% tolerance on that quote gives 950.4 tokens, a 4.96% shortfall from the reference. Raising tolerance does not improve the 960-token quote.

Which change comes from your trade, and which comes after the quote?

Uniswap’s distinction, updated 11 February 2025 and checked 13 November 2026, separates the price effect of your own trade from the difference between expected and actual execution. A quote can already reflect your trade’s impact. Comparing that quote with the final output does not measure the impact a second time.

1inch’s explanation, checked 13 November 2026, links greater impact to trade size relative to liquidity. Its routing discussion concerns available liquidity sources; it does not establish that manually splitting any order will improve execution. Use the actual route and amounts, not a general slogan about splitting trades.

    How do 1,000 reference tokens become 955 received?

    Take a hypothetical exact-input swap: the input amount stays fixed, and every output figure uses the same token and units. A model reference gives 1,000 output tokens before the trade’s own impact; the quote is 960 and execution is 955. Exclude standalone fees and other effects for this illustration. The reference is an analytical benchmark, not an amount you were guaranteed able to trade.

    In this simplified model, attribute the reference-to-quote reduction entirely to impact. An actual interface may define its displayed impact differently or include fees in a quote; inspect its method before reproducing this label. The amount comparison itself remains reproducible as long as the baselines are stated.

    • Reference to quote: (1,000 − 960) ÷ 1,000 × 100 = 4%.
    • Quote to execution: (960 − 955) ÷ 960 × 100 = 0.520833%, rounded.
    • Reference to execution: (1,000 − 955) ÷ 1,000 × 100 = 4.5%.
    • The first percentage uses 1,000 as denominator; the second uses 960. Adding 4% and 0.520833% gives the wrong combined percentage.

    What does a 1% tolerance actually allow in this model?

    Apply tolerance to the quoted output: 960 × (1 − 0.01) = 950.4 tokens. That illustrative minimum is 49.6 below the original 1,000 reference, or 4.96%. With consistent baselines, combined adverse shortfall = 1 − (1 − impact) × (1 − slippage). Using fractions gives 1 − 0.96 × 0.99 = 0.0496. The difference from 5% comes from applying the second reduction to 960, not 1,000.

    This is the threshold calculation for this model, not proof that a particular transaction encodes that threshold. Uniswap’s settings guidance, updated 20 July 2026 and checked 13 November 2026, exposes automatic or custom slippage and the maximum in swap details. Too low may fail; too high can permit fewer tokens. Read the actual transaction minimum and provider rules. A calculator cannot enforce protection.

      Can you reconcile the figures with the site calculator?

      In our slippage calculator, enter quoted output 960, executed output 955, illustrative tolerance 1 and separate fees 0. It reports signed slippage of about 0.520833%, a 950.4-token threshold, execution at or above that threshold, net output of 955 and an all-in shortfall from the quote of 5 tokens. It does not calculate price impact or tell you a safe setting.

      Now make one explicit change: suppose there is a separate 2-token fee not already deducted in the executed amount. Enter fees 2. Net output becomes 953 and quote-to-net shortfall becomes 7 tokens. Signed slippage remains 5 ÷ 960 × 100 because that output comparison precedes the separately entered fee. Our calculator worked examples explain the fields; this article adds the separate reference-price baseline.

        Where do network costs and embedded fees belong?

        Keep the accounting boundary visible. If the quote already includes a liquidity-provider fee, do not subtract it again. If the execution amount is already net of a token charge, do not enter that charge a second time as a separate fee. These are reconciliation checks, not assumptions that every interface handles fees in the same way.

        Ethereum’s gas documentation, checked 13 November 2026, describes gas as computational effort and explains transaction fees. A network charge is a separate cost from the output-token shortfall above. Our network-fee guide covers that distinction. Do not add an ETH-denominated fee directly to a count of another token; any conversion needs a stated exchange rate and time. No current market rate is used here.

          Common mistakes before increasing tolerance

          Raising tolerance does not restore output already missing from the quote because of impact. Nor is tolerance an automatic deduction: a 1% setting does not mean every successful swap loses exactly 1%. Check the displayed quote first, then the permitted execution range. Comparing only percentages can hide the fact that a quote is already substantially below your reference.

          A swap within tolerance can still lose substantial value. Tolerance does not verify a token, make an unknown contract safe or protect against later price collapse. 1inch also warns that high tolerance can expose trades to sandwich attacks. Review token approvals and revocation separately; changing execution settings does not remove spending permission. If the quote or contract cannot be explained, declining the swap is an available choice.

            What does “price impact” mean?

            It is the effect of your own trade on price, distinct from later quote-to-execution changes. Trade size relative to available liquidity matters.

            Our 4% example assigns the whole reference-to-quote reduction to impact solely to isolate the arithmetic. A live interface’s displayed percentage needs its own definition.

              Is a 0.1% slippage tolerance suitable?

              If you mean 0.1%, it is a tolerance setting, not a quality score. The amount, route and execution conditions determine whether a setting is workable.

              For the hypothetical 960-token quote, 0.1% gives 959.04 tokens as an illustrative threshold. That calculation does not recommend using it; too-tight settings may fail.

                Is a higher slippage tolerance better?

                Higher tolerance widens the adverse execution range you are willing to accept. It does not improve the current quote or remove impact.

                It may avoid some failures while allowing worse output. There is no universal safe percentage established by the primary sources used here.

                  Practical checklist

                  • Record input amount, token contracts, network, route and the time of the quote.
                  • Identify what reference price the interface uses for its impact figure; do not assume it was executable for your size.
                  • Record the quoted output and the minimum output encoded in the transaction, using the same asset and units.
                  • List which fees are already included and which are genuinely separate; keep network charges in their original units.
                  • After execution, compare actual output with the saved quote, then reconcile separate fees once.
                  • If a quote changes or the minimum is unexplained, stop and review rather than repeatedly increasing tolerance.

                  Sources and further reading

                  Fact-checked: . External sources open in a new tab.

                  1. Price Impact vs Price Slippage (checked 13 November 2026 · updated 2025-02-11)Uniswap Labs
                  2. Price impact vs. price slippage in DeFi (checked 13 November 2026)1inch
                  3. How to change slippage on the Uniswap Web app (checked 13 November 2026 · updated 2026-07-20)Uniswap Labs
                  4. Gas and fees (checked 13 November 2026)ethereum.org
                  ← More guides